FortisBC Trade Ally Boiler Installation in Port Coquitlam
A boiler replacement is a smaller disruption than most homeowners expect. The distribution in the walls and floors stays exactly where it is. The boiler is the only piece that changes, and for most Port Coquitlam homes the heat is back on the same evening. What takes care and experience is the step before installation day: examining the existing piping, testing flow through each zone, and matching the new unit to what the distribution actually needs. Eaton's Heating installs condensing and combi boilers from Navien, Viessmann, and Bosch across Port Coquitlam. Every project starts with a free in-home assessment and ends with a written, all-in price. Financeit at zero percent over 12 months is available.
See what our customers have to say
Brands Serviced
Years of Experience
Homes Served and Counting
The assessment starts with what the home already has. In Port Coquitlam's older homes around Central Port Coquitlam, Mary Hill, and Lower Mary Hill, that means cast-iron radiators that have been heating the home for decades, connected by copper or steel piping that has accumulated mineral deposits and seen ad-hoc modifications through previous boiler replacements. The radiators themselves are almost always sound, because cast iron holds up indefinitely when the water quality is maintained. The piping and valves between the boiler and those radiators are what determine the scope of the project: corroded fittings, seized zone valves, and scale that has narrowed the flow path over the years. All of it gets tested during the assessment and accounted for in the estimate, so the written price reflects the actual project.
Citadel Heights homes from the late 1970s through the 1990s sometimes use in-floor radiant in additions or lower levels, where the boiler feeds heated slabs at a lower water temperature through a mixing valve and manifold. Riverwood and the newer townhomes in the Fremont area are more likely to have modern combi setups, where a single wall-hung unit handles space heating and domestic hot water. A combi replaces two appliances in one, freeing up the mechanical room and eliminating the cost of keeping a hot water tank heated around the clock. Whether a combi works for your household depends on how much hot water gets used at the same time: one or two bathrooms with typical family demand is well within a combi's range, while three or more bathrooms with overlapping showers and appliances can exceed the flow rate. We sort that out during the assessment based on actual usage rather than guessing from the spec sheet.
The damp valley-floor conditions in Port Coquitlam affect boiler installation decisions in ways that are easy to miss. Basements and crawl spaces stay humid through the wet season, and the piping assembly that connects the new boiler to the distribution sits in that environment year round. Expansion vessel connections, circulator pump housings, and threaded fittings all deteriorate faster in sustained moisture. When we assess the existing piping during a replacement, we are looking at what the dampness has already done and what it will do to the new components over the next 15 to 20 years. Venting termination on a condensing boiler also needs careful placement: PVC exhaust on homes near the Coquitlam River or in lower-lying parts of Mary Hill has to be positioned where rain and ground-level moisture will not cause ice buildup during the coldest weeks.
Bosch covers the mid-range with solid performance and minimal maintenance across both combi and heating-only configurations. Viessmann is the premium tier, built for homeowners who plan to stay in the house long term, and its higher-capacity options serve larger multi-zone homes where the boiler is feeding radiators, radiant floors, and domestic hot water across a large home. Navien's combi and heating-only condensing lines handle most straightforward replacements in Port Coquitlam, where the project is a single boiler feeding a manageable number of zones. We carry all three and recommend based on what the distribution needs, the household's hot water habits, and the budget. Eaton's Heating holds Technical Safety BC licence LGA0200006, FortisBC Trade Ally status, BBB A+ accreditation, HPCN registration, and full WorkSafeBC coverage. Our 400-plus Google reviews at 4.9 reflect systems that heat evenly from the first season.
We pull the old boiler, connect the new unit through a full piping assembly with isolation valves, expansion tank, air separator, circulator, and backflow preventer, run the venting, complete gas fitting and electrical, then commission the system. Commissioning means purging air from every loop, measuring and adjusting flow until every zone heats evenly, and registering factory warranties before we leave. Most replacements in Port Coquitlam finish in a single day. If the current boiler has a fixable problem rather than being at the end of its useful life, our boiler repair page for Port Coquitlam is the place to start, because a $400 pump repair on a sound boiler is better value than replacing the whole unit. For homeowners considering a switch from hydronic to forced air, we install furnaces and heat pumps too, though when the distribution is already in the walls, keeping it is usually the better path.
A combi boiler handles space heating and domestic hot water from one wall-hung unit, which means no tank in the mechanical room and no cost to keep stored water hot. For households with one or two bathrooms and typical demand, a combi does both jobs well and simplifies the system. The honest limit is how much hot water the household uses at the same time: when multiple showers, a dishwasher, and a washing machine overlap, the combi cannot keep up. A household that regularly runs into that limit is better served by a heating-only boiler paired with a separate tankless or tank water heater, so neither function compromises the other.
The assessment resolves this by talking through your household's actual morning and evening routine rather than sizing from a number on a page. We also confirm whether current FortisBC and CleanBC rebate programs apply to the specific equipment being quoted and show both the gross and net cost in the written estimate. As a FortisBC Trade Ally we file the application after installation. Financeit at zero percent over 12 months is available on every project.
Licensed Gas Contractor (LGA0200006)
Authorized Dealer and Installer
Certified Fireplace Dealer
Have a question about your HVAC system? Book an appointment using the form below, or call (604) 535-8434 for immediate help.
A boiler-to-boiler replacement on existing healthy piping, where the new condensing unit connects to the same zones and distribution without modification, typically runs $5,000 to $8,000 all-in. That covers the boiler, piping assembly, venting, gas fitting, electrical, commissioning, removal, and disposal. Projects involving combi conversions, zone additions, piping corrections, or larger multi-zone systems climb into the $8,000 to $14,000 range. The estimate is free, written, and itemized, and the number on it is the final number.
Yes, and that is the standard path. Radiators, especially cast iron, routinely outlast multiple boilers. The variables are the piping and valves between them: scale deposits can restrict flow, corroded fittings can weep under the pressures of a modern system, and zone valves that barely worked on the old unit may not respond to a new one. We check flow rates and valve response at every loop during the assessment. If flushing or valve work is required, that scope goes into the written estimate and gets done during the replacement, not after.
Most replacements in Port Coquitlam finish in a single day when the piping is sound and the new unit connects to the existing layout without modification. The heat goes off mid-morning when the old boiler comes out and returns the same evening once the new system fires and the loops are purged. Homes with hydronic slabs barely feel the gap because the concrete holds its heat through a working day. Projects that involve flushing scaled piping, adding zones, or converting to a combi may extend to two days. The estimate confirms which yours is.
That depends on what failed. Circulator pumps, zone valves, expansion vessels, and ignition parts are all worth repairing on a boiler that is otherwise in good shape. When the heat exchanger is cracked or scaled beyond cleaning on a unit past twenty years, the repair cost approaches what a new condensing boiler would cost to install, and the new unit comes with a factory warranty and substantially better efficiency. We show both paths with real numbers. If the repair makes sense, we do it.
We handle both. The Technical Safety BC gas permit is filed before work starts and the inspection is booked after. On the incentive side, FortisBC runs programs on qualifying high-efficiency boiler installations that can reduce the net cost. We confirm what applies during the assessment, show the before and after numbers in the estimate, and submit the Trade Ally application once the install passes inspection.
Commissioning is the step that makes the heat even. Air gets purged from every loop, starting from the highest points where it naturally collects. Flow gets measured and adjusted zone by zone so the farthest radiator or loop gets its full share of circulation. Combustion is checked, the condensate path is confirmed clear, and factory warranties are registered. A boiler that was installed correctly but never commissioned will leave cold spots, noisy radiators, and uneven zones that the homeowner assumes are normal. They are not. We commission every system we install.
Simply complete our form to make an appointment. A member of our team will be in touch to confirm your appointment.
